Are you trying to locate help and advice around Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is also a moderately difficult task. If the old tub is conveniently available, the project can move rapidly; if you have to open up a wall surface to eliminate the old bathtub as well as position the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub as well as set in the new one. Make sure you have actually certified yourself for the job and fit attempting it. Rather than hiring a contractor to take over a halfway-completed job, it is better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new tub in your shower room if you have already purchased a new bathtub and also don't require to alter the plan of your previous water system pipelines.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be fairly problematic as a result of the limited gain access to that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning throughout this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in location in between the faucet as well as the sink. Protect the faucet in position with the producer offered backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Making use of the two wood boards under its feet, put the tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small points.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bath tub until the spirit level reads degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water as well as examine all joints and also brand-new pipework for leaks and also tighten them if needed. Fill the bathtub and likewise inspect the overflow outlet as well as the normal outlet for leakages.
Lastly, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will certainly resolve it into its final placement.
Getting ready for the Installation
To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to stop stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, causing the water to pass through the wall surface in between the bath and the tiling, resulting in issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water before securing, to enable the activity experienced when the tub remains in use. The sealant can break relatively early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very focused on How to Install a Bathtub Yourself and I'm hoping you enjoyed the post. Enjoyed reading our posting? Please share it. Help another person locate it. Many thanks for your time. Please pay a visit to our website back soon.
Top service, one call.